Can I Install A Bathtub Myself?
Can I Install A Bathtub Myself?
Blog Article
Just about every person seems to have their own thinking in relation to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the job can move immediately; if you need to open a wall to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the level reviews level.
To install faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the bathtub needs to wait up until the tub has been made use of a minimum of once as this will resolve it into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the producer given backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind should be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealer can fracture rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very interested by Installing A Bathtub and I am assuming you liked the entire article. So long as you appreciated our page kindly be sure to pass it around. Bless you for your time. Kindly visit our site back soon.
Visit Website
Report this page